Flowserve 191 000 Series User Manual download pdf

111.00

Flow Control Division

Kammer Control Valves

1 GENERAL INFORMATION

These instructions are designed to support you when

unpacking, installing and performing maintenance

work on the valves. Users and maintenance person-

nel should carefully read these instructions before

installing, operating or performing maintenance

work. There is a separate set of instructions for ac-

cessories (special seat/plug fittings, diaphragm ac-

tuators, handwheels, special seats, etc.).

These instructions do not contain any information

on Kämmer positioners. For this, see correspond-

ing instructions for the installation, maintenance,

troubleshooting, adjustment and operation of

Kämmer positioners.

To avoid damage or injury to personnel or equip-

ment, always heed all warnings and instructions.

Unprofessional reconditioning, the use of foreign

replacement parts or the performance of other

maintenance steps than those described here, may

cause a loss of efficiency or lead to personnel in-

jury or damage to parts, and render the warranty

void

1.1 UNPACKING

1.1.1 Each delivery includes a packing slip. When unpack-

ing, check all delivered valves and accessories us-

ing this packing slip.

1.1.2 Report transport damage to the carrier immediately.

1.1.3 In case of discrepancies, contact your nearest dealer.

1.2 INSTALLATION

1.2.1 Clean tubing prior to installing.

1.2.2 If possible, install the valve in an upright position (ac-

tuator on top), to ease maintenance. An upright in-

stallation position is important with low-temperature

applications, in order to keep the distance between

the packing material and the medium as large as pos-

sible. The packing material then retains the ambient

temperature as much as possible.

Important: Do not insulate extension bonnets that

are provided for hot or cold services

1.2.3 Make sure that sufficient overhead clearance above

the actuator is maintained, to allow for disassembly

of plug from the valve body (see following table).

1.2.4 After installing, check direction of flow again.

1.2.5 If the valve is to be welded into the line, make sure

that the valve is shielded from excessive heat.

1.2.6 Connect supply pressure and signal lines. Control

valves can be supplied with a positioner. The end

connections for supply pressure and signal are clearly

marked. Actuator and positioner are suitable for max.

6 bar (87 psi) supply pressure. If the supply pres-

sure exceeds the pressure specified on the name-

plate, a pressure reducing station is required. If in-

strument air is not available, install an oil separator/

air filter in the air inlet line. All connections must be

free of leaks.

Installation, Operation, Maintenance Instructions

Sanitary and Hygiene Valves

Series 191 000

Series 191 600 Steam Barrier

KMEIM9102-00 - 11.00

Actuator Clearance Actuator Clearance

size (mm) size (mm)

37/47 95 P2 140

38/48 140 P3 140

39/49 140 P4 140

39D/49D 140 P5 140

1 2 3 4

Summary of Contents

Page 1 - Sanitary and Hygiene Valves

111.00Flow Control DivisionKammer Control Valves1 GENERAL INFORMATIONThese instructions are designed to support you whenunpacking, installing and perf

Page 2 - Typical valve configuration

2 11.00Flow Control DivisionKammer Control Valves1.3 QUICK CHECK:Before operating, check the valve as follows:1.3.1 Open and close the valve, and obse

Page 3 - Kammer Control Valves

311.00Flow Control DivisionKammer Control Valves2.5 If possible, open and close valve and check for maxi-mum stroke and smooth movement of the plug st

Page 4

4 11.00Flow Control DivisionKammer Control ValvesFRANCE USA / CANADA SWITZERLANDFlowserve S.A.S. Flowserve (FCD) Flowserve S.A.SEREG KAMMER VALVES, IN

Flowserve 191 000 Series User Manual

Browse online or download User Manual for Hardware Flowserve 191 000 Series. Flowserve 191 000 Series User Manual

Summary of Contents

Related models: 191 600 Series

More documents for Hardware Flowserve 191 000 Series

Comments to this Manuals

Flowserve 191 000 Series User Manual

Browse online or download User Manual for Hardware Flowserve 191 000 Series. Flowserve 191 000 Series User Manual

Summary of Contents

Related models: 191 600 Series

More documents for Hardware Flowserve 191 000 Series

Comments to this Manuals

Related products and manuals for Hardware Flowserve 191 000 Series