Flowserve Machinery Components User Manual Page 1
Browse online or download User Manual for Hardware Flowserve Machinery Components. Flowserve Machinery Components User Manual
- Page / 16
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
1. Drawing, Brief Description, Explosion Protection, Function of a Mechanical Seal ......2
2. Safety ...............................................................3
3. General ..............................................................4
4. Transport, Storage ......................................................5
5. Equipment Check .......................................................5
6. Mechanical Seal Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
6.1 Installation of Cartridge Type Seal with Setting Plates........................8
6.2 Installation of a Cartridge Type Seal with Centring Tabs ......................9
6.3 Installation of a Component Type Seal...................................10
6.4 Installation of Seals with Hooked Type Sleeves ............................11
7. Piping Instructions .....................................................12
8. Performance Testing of Pumps ...........................................12
9. Functional Recommendations.............................................13
10. Shut Down, Disassembly ................................................14
11. System Check ........................................................15
12. Spare Parts, Repair.....................................................15
These installation instructions can be used for the following seal types:
Pusher seals: Allpac 4 series, Allpac N series, Centipac 1 series, CRO, D series, DHT
series, Europac 306, Europac 6 series, FRO, GSD, GSL, HD series, HSC,
HSH, LD, P series, Q series, RO, Simpac 3 series, SRO, U series, UHT
series.
Bellows seals: BRC series, BX series, BXH series, BXLS series, BXRH, CBR series, CBS,
GSDH, PBR, PBS, X series.
General Installation and Maintenance Instructions
for Machinery Components
USER INSTRUCTIONS
-Original Instruction-
Table of Contents page no.
Experience In Motion
Summary of Contents
Page 1 - -Original Instruction
1. Drawing, Brief Description, Explosion Protection, Function of a Mechanical Seal ...2 2. Safety ...
Page 2
106.3 Installation of a Component Type Seal See figure 8. 6.3.1 Check assembly drawing, bill of material and seal components prior to installatio
Page 3
General Installation and Maintenance Instructions for Machinery Components116.4 Installation of Seals with Hooked Sleeves (overhung pumps) See fig
Page 4
126.4.11 After bringing the unit up to operating conditions (pressure and temperature), recheck pump to driver alignment. Make adjustments as necessa
Page 5 - 5. Equipment Check
General Installation and Maintenance Instructions for Machinery Components13and face materials require special precautions to prevent damage to the se
Page 6
149.8 Liquid seal requirements: Do not start the equipment dry. Open valves to flood equipment with product. Vent all air and/or product vapor from
Page 7
General Installation and Maintenance Instructions for Machinery Components15Product may be released during removal of the mechanical seal. Safety meas
Page 8
To find your local Flowserve representative and find more about Flowserve Corporation, visit www.flowserve.comFIS144eng REV 12/2009 Printed in USAF
Page 9
21. Drawing, Brief Description, Explosion Protection, Functional Requirements This mechanical seal is designed to provide reliable performance u
Page 10
General Installation and Maintenance Instructions for Machinery Components3 ESA position statement: http://www.europeansealing.com/statements.html
Page 11
4The ultimate user must ensure that personnel assigned to handle, install and run the mechanical seal and related equipment is well acquainted with th
Page 12
General Installation and Maintenance Instructions for Machinery Components54. Transport, Storage
Page 13
65.7 The equipment must be earthed to prevent sparks due to static electricity discharge.Shaft runout should not exceed 0,05 mm (.002”) TIR (Total In
Page 14
General Installation and Maintenance Instructions for Machinery Components7Concentricity of the shaft to the seal chamber bore should be within 0,025
Page 15
86.1 Installation of Cartridge Type Seal with Setting Plates See figure 6.6.1.1 Check assembly drawing, bill of material and seal assembly
Page 16 - Order #___________________
General Installation and Maintenance Instructions for Machinery Components96.2 Installation of a Cartridge Type Seal with Centring Tabs See figure
Related products and manuals for Hardware Flowserve Machinery Components
Hardware Flowserve PSS II User Manual
(16 pages)
(16 pages)
Hardware Flowserve ISC1BX User Manual
(8 pages)
(8 pages)
Hardware Flowserve ISC1PX User Manual
(8 pages)
(8 pages)
Hardware Flowserve ISC1EX User Manual
(8 pages)
(8 pages)
Hardware Flowserve GCX Series User Manual
(12 pages)
(12 pages)
Hardware Flowserve Allpac MP User Manual
(4 pages)
(4 pages)
Hardware Flowserve ISC2BB User Manual
(12 pages)
(12 pages)
Hardware Flowserve ISC2PP User Manual
(12 pages)
(12 pages)
Hardware Flowserve D Series User Manual
(4 pages)
(4 pages)
Hardware Flowserve SLD User Manual
(8 pages)
(8 pages)
© 2020, manymanuals.com. All rights reserved. | 2.367 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals