Flowserve DS User Manual download pdf (Page 34)

DS USER INSTRUCTIONS ENGLISH 71576283 - 02/13

Page 34 of 36 flowserve.com

8.2 Sectional drawing parts list

Item

Designation

1110 Pump casing

1221 Casing cover

1500-01 Wear ring

1500-02 Wear ring

2110 Shaft

2250 Impeller

2450-01 Shaft sleeve

2450-02 Shaft sleeve

2540-01 Deflector

2540-02 Deflector

2900 Washer

2905 Washer

3011 Radial ball bearing

3012 Radial roller bearing

3126 Shim

3134 Support foot

3200 Bearing housing

3260-01 Bearing cover

3260-02 Bearing cover

3712 Bearing nut

3852 Constant level oiler

3853 Grease nipple

3863 Grease regulator

4120 Gland

4130 Gland packing

4134 Lantern ring

4200 Mechanical seal

4213 Carrier for mechanical seal

4590-01 Gasket

4590-02 Gasket

4590-03 Gasket

4590-04 Gasket

4590-05 Gasket

Item

Designation

4590-06 Gasket

4590-07 Gasket

4590-08 Gasket

4590-09 Gasket

4610-01 O-ring

4610-02 O-ring

6515 Drain plug

6521 Vent plug

6541 Lock washer

6544 Circlips

6569-01 Screwed plug

6569-02 Screwed plug

6569-03 Screwed plug

6569-04 Screwed plug

6569-05 Screwed plug

6569-06 Screwed plug

6570-01 Hexagon socket grub screw

6570-02 Hexagon socket grub screw

6572-01 Stud

6572-02 Stud

6572-03 Stud

6577-01 Hexagon bolt

6577-02 Hexagon bolt

6577-03 Hexagon bolt

6577-04 Hexagon bolt

6581-01 Hexagon nut

6581-02 Hexagon nut

6581-03 Hexagon nut

6810 Grooved pin

6700-01 Key

6700-02 Key

9331 Cover plate

8.3 General arrangement drawing

The typical general arrangement drawing and any

specific drawings required by the contract will be sent

to the Purchaser separately unless the contract

specifically calls for these to be included into the

User Instructions. If required, copies of other

drawings sent separately to the Purchaser should

be obtained from the Purchaser and retained with

these User Instructions.

9 CERTIFICATION

Certificates determined from the Contract

requirements are provided with these instructions

where applicable. Examples are certificates for CE

marking, ATEX marking etc. If required, copies of

other certificates sent separately to the Purchaser

should be obtained from the Purchaser for

retention with these User Instructions.

10 OTHER RELEVANT

DOCUMENTATION AND MANUALS

10.1 Supplementary User Instructions

Supplementary instructions such as for a driver,

instrumentation, controller, seals, sealant system

etc are provided as separate documents in their

original format. If further copies of these are

required they should be obtained from the supplier

for retention with these User Instructions.

10.2 Change notes

If any changes, agreed with Flowserve, are made to

the product after its supply, a record of the details

should be maintained with these User Instructions.

10.3 Additional sources of information

Reference 1:

NPSH for Rotor dynamic Pumps: a reference

guide, Euro pump Guide No. 1, Euro pump &

World Pumps, Elsevier Science, United Kingdom,

1999.

Reference 2:

Pumping Manual, 9

edition, T.C. Dickenson,

Elsevier Advanced Technology, United Kingdom,

1995.

Reference 3:

Pump Handbook, 2

edition, Igor J. Karassik et al,

McGraw-Hill Inc., New York, 1993.

Reference 4:

ANSI/HI 1.1-1.5, Centrifugal Pumps -

Nomenclature, Definitions, Application and

Operation.

Reference 5:

ANSI B31.3 - Process Piping.

1 2 ... 29 30 31 32 33 34 35 36

Comments to this Manuals

No comments

Flowserve DS User Manual Page 34

Comments to this Manuals

Related products and manuals for Pumps Flowserve DS